SpeedyBee BLS 50A 30x30 4-in-1 ESC

IMU(Gyro) - BMI270
USB Port Type - Type-C
Barometer - Built-in
OSD Chip - AT7456E chip
BLE Bluetooth - Supported. Used for Flight Controller configuration
DJI Air Unit Connection Way - Two ways supported: 6-pin connector or direct soldering.
Blackbox MicroSD Card Slot:
*Betaflight firmware requires the type of the microSD card to be
either Standard (SDSC) or High capacity (SDHC),so extended
capacity cards (SDXC) are not supported(Many high-speed U3
cards are SDXC). Also the card MUST be formatted with the
FAT16 or FAT32 (recommended) filesystems. So, you could
use any SD card less than 32GB, but the Betaflight can only
recognize 4GB maximum. We suggest you use this
3rd party formatting tooland choose 'Overwrite format' then format
your card.

BetaFlight Camera Control Pad - Yes(CC pad on the front side)
Current Sensor Input - Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
Power Input - 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output - 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side,
and 4x LED 5V pads. The total current load is 2A.

9V Output - 2 groups of 9V output, one +9V pad on front side and other included in a connector
on bottom side. The total current load is 2A.

3.3V Output - Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output - Supported. Designed for receiver and GPS module even when the FC is powered
through the USB port. Up to 1A current load.

ESC Signal - M1 - M4 on bottom side and M5-M8 on front side.

UART - 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)

ESC Telemetry UART - R4(UART4)
I2C - Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad:
Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED
controlled by Betaflight firmware.

Buzzer - BZ+ and BZ- pad used for 5V Buzzer

BOOT Button:

Supported.
[A]. Press and hold BOOT button and power the FC on at the
same time will force the FC to enter DFU mode, this is for
firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the
BOOT button can be used to controller the LED strips
connected to LED1-LED4 connectors on the bottom side.
By default, short-press the BOOT button to cycle the LED
displaying mode. Long-press the BOOT button to switch
between SpeedyBee-LED mode and BF-LED mode.
Under BF-LED mode, all the LED1-LED4 strips will be
controlled by Betaflight firmware.

RSSI Input - Supported. Named as RS on the front side.

SmartPort - Use any TX pad of UART for the SmartPort feature.

Supported Flight Controller Firmware - BetaFlight(Default), EMUFlight, INAV

Firmware Target Name - SPEEDYBEEF405V3

Mounting - 30.5 x 30.5mm( 4mm hole diameter)

Dimension - 41.6(L) x 39.4(W) x 7.8(H)mm

Weight - 9.6g

Product Name - SpeedyBee BLS 50A 30x30 4-in-1 ESC

Firmware - BLHeli_S JH50

Wireless Configuration:
Full Configuration Supported in the SpeedyBee app

Continuous Current - 50A * 4

Burst Current - 55A(5S)

TVS Protective diode - Yes

External Capacitor - 1500uF Low ESR Capacitor(In the package)

ESC Protocol - DSHOT300/600

Power Input - 3-6S LiPo

Power Output - VBAT

Current Sensor - Support (Scale=386 Offset=0)

Mounting - 30.5 x 30.5mm( 4mm hole diameter)

Dimension - 45.6(L) * 44(W) * 6.1mm(H)

Weight - 13.8g